Product family
Temporary works have to stand firm from the day they go up to the day they come down. Corona makes the steel parts that hold them: cuplock standards and ledgers, steel planks for the working decks, base jacks and heavy U-head jacks to level and top out a tower, adjustable props with their pins, nuts and threaded tubes, and trench struts to hold an excavation open. Each part is made to the size series and standard the buyer specifies.
Explore scaffolding & shoring systems
Where it's used
Building facades, plant rooms, tanks and stair towers all need safe access at height while the work goes on. System scaffold goes up fast in regular bays and takes a full working deck at each lift. Cuplock System, Planks and Screw Jack with Base Plate & Wing Nut cover it.
Wet concrete has to be carried until it can carry itself, and the slab above often needs back-propping while the next floor is poured. Props set to height under the formwork do that job, floor by floor. Props, Threaded Tube, Prop Nut and G Pin cover it.
Bridge decks, transfer slabs and high ceilings need taller, heavier support than a single prop can give. Towers built with adjustable jacks top and bottom carry the beams that hold the formwork. Hi-Load Screw Jack with Wing Nut, Screw Jack with Base Plate & Wing Nut and Cuplock System cover it.
Drainage runs, utility trenches and pit excavations must be kept open while people work inside them. Struts set across the trench hold its sides back against the ground. Trench Struts and G Pin cover it.
Hire companies and contractors keep large fleets of props running, and pins go missing and nuts wear. Spare parts made to the same size series keep every prop in use. G Pin, Prop Nut and Threaded Tube cover it.
Six families
Product family
The cup-jointed frame of standards, ledgers and transoms you build access scaffold from.
Product family
The steel boards you lay across each lift to stand and work on.
Product family
Threaded jacks that level a scaffold at the foot and carry beams at the top of a tower.
Product family
Adjustable steel props in sizes #0 to #4, set to height under formwork or a slab.
Product family
The pin, nut and threaded sleeve you replace to keep props working.
Product family
Telescopic struts you set across an excavation to hold its sides.
Scaffolding and shoring systems
CUPLOCK
Standards carry cups every half metre, and each ledger and transom locks into a cup node with no loose fittings. Bays of 0.6 to 3.0 m go up in regular lifts on base jacks.
Diameter: 2 in (N.B.) / 48.3 mm (O.D.), 3.2 or 4.0 mm wall · Length: 3-12 ft / 1-4 m; verticals in 0.5 m steps
SpecificationsDiameter: 1-1/4, 1-1/2 in (N.B.) / 33.7, 38, 38.1 mm (O.D.); 26-48 mm to order · Length: 24-36 in / 600-900 mm
SpecificationsWidth: 9, 10, 12 in / 200-500 mm; 225, 230, 238, 250, 300, 320 mm common · Depth: 38, 50, 57, 63, 76 mm
SpecificationsWORKING DECKS
Steel boards laid side by side across the transoms make the deck at each lift, on system scaffold or tube-and-fitting scaffold.
Width: 9, 10, 12 in / 200-500 mm; 225, 230, 238, 250, 300, 320 mm common · Depth: 38, 50, 57, 63, 76 mm
SpecificationsDiameter: 1-1/4, 1-1/2 in (N.B.) / 33.7, 38, 38.1 mm (O.D.); 26-48 mm to order · Length: 24-36 in / 600-900 mm
SpecificationsPROPS
An inner tube slides inside a threaded outer tube. A pin sets the height in steps, and a nut on the thread takes it the rest of the way.
Size: #0, #1, #2, #3, #4 · Height: #0: 1.1-1.8 m; #1: 1.75-3.12 m; #2: 2.0-3.4 m; #3: 2.59-3.96 m; #4: 3.2-4.87 m
Specifications
Size: #0, #1, #2, #3, #4 · Tube: 60.3 mm O.D., 3.6 mm wall
Specifications
Size: #0, #1, #2, #3, #4 · Thread: 4 TPI, to suit 60.3 mm threaded tubes
SpecificationsFALSEWORK
Towers stand on base jacks and carry beams in U-heads or fork heads at the top, so the formwork sits at exactly the right level.
Diameter: 1-1/4, 1-1/2 in (N.B.) / 48.3, 60.3 mm (O.D.) · Length: 30-120 in / 760 mm-3 m
SpecificationsDiameter: 1-1/4, 1-1/2 in (N.B.) / 33.7, 38, 38.1 mm (O.D.); 26-48 mm to order · Length: 24-36 in / 600-900 mm
SpecificationsDiameter: 2 in (N.B.) / 48.3 mm (O.D.), 3.2 or 4.0 mm wall · Length: 3-12 ft / 1-4 m; verticals in 0.5 m steps
SpecificationsTRENCH SHORING
Struts span the excavation between walings or trench sheets on each side, extended to fit and locked with a pin and screw.
Questions answered
Complete product range
Each card shows the product role and first useful specification fields before the full detail page. Know a component by another name? Find it in the trade-names list.
Diameter: 1-1/4, 1-1/2 in (N.B.) / 33.7, 38, 38.1 mm (O.D.); 26-48 mm to order · Length: 24-36 in / 600-900 mm
SpecificationsDiameter: 1-1/4, 1-1/2 in (N.B.) / 48.3, 60.3 mm (O.D.) · Length: 30-120 in / 760 mm-3 m
SpecificationsWidth: 9, 10, 12 in / 200-500 mm; 225, 230, 238, 250, 300, 320 mm common · Depth: 38, 50, 57, 63, 76 mm
SpecificationsDiameter: 2 in (N.B.) / 48.3 mm (O.D.), 3.2 or 4.0 mm wall · Length: 3-12 ft / 1-4 m; verticals in 0.5 m steps
SpecificationsSize: #0, #1, #2, #3, #4 · Height: #0: 1.1-1.8 m; #1: 1.75-3.12 m; #2: 2.0-3.4 m; #3: 2.59-3.96 m; #4: 3.2-4.87 m
SpecificationsSize: #0, #1, #2, #3, #4 · Diameter: 10-18 mm
SpecificationsSize: #0, #1, #2, #3, #4 · Thread: 4 TPI, to suit 60.3 mm threaded tubes
SpecificationsSize: #0, #1, #2, #3, #4 · Tube: 60.3 mm O.D., 3.6 mm wall
SpecificationsSize: #0, #1, #2, #3, #4 · Length: #0: 0.32-0.47 m; #1: 0.49-0.73 m; #2: 0.69-1.09 m; #3: 1.03-1.73 m
Specifications