Corona SteelIndustry Pvt Ltd
HE

בחירת שפה

חיפוש מוצריםבקשו הצעת מחיר
HE

בחירת שפה

תפריט
מפת האתר07 ערכים
Corona Steelהוקמה ב-1955
Resources/Threads/BSP vs NPT

Threads

Pipe threads: BSP (G, R, Rp, Rc) vs NPT

BSP pipe threads use the 55° Whitworth form, either parallel (G, ISO 228-1) or taper (R, Rp, Rc, ISO 7-1 and EN 10226), while NPT uses a 60° form tapered 1 in 16 to ASME B1.20.1. The two systems differ in thread angle and, at most sizes, threads per inch, so BSP and NPT fittings are not interchangeable.

Names by standard

Standards in each region

RegionSystemDesignationתקןMatch
USANational pipe thread1/2-14 NPT60° taper thread sealed with tape or compound. NPTF (Dryseal) is ASME B1.20.3; NPS/NPSM are straight versions.ASME B1.20.1Same material
UKBS EN / BS EN ISOG1/2, R1/2, Rp1/2, Rc1/2Formerly BS 2779 (parallel, replaced by BS EN ISO 228-1) and BS 21 (taper, replaced by BS EN 10226). Trade names BSPP and BSPT are still used.BS EN ISO 228-1 (parallel), BS EN 10226-1 and -2 (taper)Same material
EUISO / ENG1/2, R1/2, Rp1/2, Rc1/2EN 10226-1 covers taper external R with parallel internal Rp; EN 10226-2 covers taper external R with taper internal Rc.ISO 228-1, ISO 7-1, EN 10226-1 and -2Same material
הודוISR1/2, Rp1/2, Rc1/2 (IS 554); G1/2 (IS 2643)IS 554 is identical to ISO 7-1 (threads that seal on the thread). IS 2643 covers parallel threads that do not seal on the thread, aligned with ISO 228-1.IS 554, IS 2643Same material
JapanJISG1/2, R1/2, Rp1/2, Rc1/2Based on ISO 228-1 and ISO 7-1. Older Japanese marks PF (parallel), PT (taper) and PS (parallel internal) are still seen.JIS B 0202 (parallel), JIS B 0203 (taper)Same material

Thread form

גיאומטריה

BSP thread angle
55°, rounded crests and roots (Whitworth form)
NPT thread angle
60°, flat crests and roots
Taper (R, Rc, NPT)
1 in 16 on diameter (62.5 mm per metre)
BSP parallel
G: no taper; seals with a gasket, washer or O-ring, not on the thread
BSP taper
R external taper; Rc internal taper; Rp internal parallel, used with R to seal on the thread
מידה
Nominal size refers to pipe bore, not thread diameter (1/2 BSP is about 20.96 mm major diameter)
Pitch expressed as
Threads per inch

Size chart

Common sizes

Nominal sizeBSP major diameter (mm)NPT pipe OD (mm)BSP TPINPT TPI
1/89.72810.2872827
1/413.15713.7161918
3/816.66217.1451918
1/220.95521.3361414
3/426.44126.6701414
133.24933.4011111.5
1 1/441.91042.1641111.5
1 1/247.80348.2601111.5
259.61460.3251111.5

BSP major diameter is the basic (gauge-plane) diameter, the same for G and R threads. NPT column is the actual outside diameter of the pipe (0.405–2.375 in). BSP threads are 55°, NPT threads 60°.

In practice

Uses and compatibility

Where it is used

  • Water, gas, steam and air piping and fittings
  • Hydraulic and pneumatic ports (G parallel threads with bonded seals or O-rings)
  • Valves, pumps, gauges and instrument connections
  • Conduit and threaded pipe nipples
  • NPT in North American plumbing, oil and gas, and process equipment; BSP in the UK, Europe, India, Japan and most of Asia

What interchanges

  • BSP and NPT are not interchangeable. The thread angles differ (55° vs 60°), crest and root shapes differ, and at 1/8, 1/4, 3/8 and 1 in and above the TPI differs.
  • At 1/2 and 3/4 both have 14 TPI, so a BSP fitting may engage an NPT port for a few turns, but the flanks do not seat and the joint is likely to leak under pressure. Use an adapter.
  • BSP parallel (G) threads do not seal on the thread; they need a gasket, bonded washer or O-ring. Do not rely on thread tape in a G joint.
  • A taper R external thread is designed to seal in either an Rp (parallel) or Rc (taper) internal thread, as set out in EN 10226-1 and -2.
  • NPT and NPTF (Dryseal) have the same pitches and can be assembled together, but only matching NPTF pairs are designed to seal without sealant.
  • BSP and BSW share the 55° form but not diameters: a 1/4 BSP thread is about 13.2 mm, not 1/4 in.

תשובות לשאלות

Common questions

What is the difference between BSP and NPT?

BSP uses a 55° thread angle with rounded crests; NPT uses 60° with flat crests. Most sizes also have different threads per inch, for example 1/4 BSP has 19 TPI and 1/4 NPT has 18.

Can I connect a BSP fitting to an NPT thread?

Not reliably. Even at 1/2 and 3/4, where both have 14 TPI, the different thread angles prevent a pressure-tight seat. Use a BSP-to-NPT adapter.

What do G, R, Rp and Rc mean on pipe threads?

G is a parallel thread that seals with a gasket or O-ring (ISO 228-1). R is an external taper thread, Rc an internal taper thread and Rp an internal parallel thread; R, Rc and Rp seal on the thread (ISO 7-1, EN 10226).

Why is a 1/2 inch pipe thread about 21 mm in diameter?

Pipe thread sizes are named after the nominal bore of the pipe, not the thread diameter. The thread is cut on the outside of the pipe wall, so 1/2 BSP measures about 20.96 mm and 1/2 NPT pipe about 21.3 mm across.

Which pipe thread standard does India use?

India uses BSP-form threads: IS 554 for taper threads that seal on the thread (identical to ISO 7-1) and IS 2643 for parallel threads that do not.

From the Corona catalog

Need a part made to this specification?

Send the drawing, the material or grade, the finish, the quantity and the delivery country. The team reviews the requirement and the manufacturing route.

פתחו פנייה

Keep reading

BSW / BSFBSW (British Standard Whitworth) and BSF (British Standard Fine) are 55° inch threads with rounded crests and roots, defined in the UK by BS 84.UNC / UNFUNC (Unified coarse) and UNF (Unified fine) are 60° inch threads designated by diameter and threads per inch, such as 1/2-13 UNC or 1/2-20 UNF.ISO metric (M)ISO metric threads are 60° V-threads designated by M, the major diameter in millimetres and, for fine pitches, the pitch in millimetres (M12 is coarse, M12×1.25 is fine).Rolled vs cut threadsA rolled thread is cold formed by pressing hardened dies into a blank, while a cut thread is machined by removing metal.

References

Sources

  1. British Standard Pipe (Wikipedia) — BSP TPI, major diameters, G/R/Rp/Rc designations, 1:16 taper.
  2. National pipe thread (Wikipedia) — NPT TPI, pipe OD, 60° angle, ASME B1.20.1 and B1.20.3.
  3. Roymech: Pipe threads (BS 21, BS 2779, EN 10226, ISO 228) — Supersession of BS 21 and BS 2779.
  4. EN 10226-1:2004 Pipe threads where pressure-tight joints are made on the threads
  5. BIS: IS 554 Pipe threads where pressure-tight joints are made on the threads
  6. InfraLens: IS 2643 Pipe threads where pressure-tight joints are not made on the threads
  7. JIS screw thread standards list (JIS B 0202, B 0203)

Values summarize published limits and typical data. The governing standard and the current edition control; check them before specifying.